ERROR CODES
| SCSI CODE | DESCRIPTION |
| 1 | Error Allocating SRB |
| SCSI CODE | COMPLETION ERRORS |
| 50 | SCSI Request Still In Progress |
| 51 | SCSI Request Completed Ok |
| 52 | SCSI Request Aborted |
| 54 | SCSI Request Error |
| SCSI CODE | COMMAND FINISHED WITH HOST ADAPTER EXECUTION ERRORS |
| 100 | Ok |
| 111 | SCSI Command Timeout |
| 113 | SCSI Message Rejected |
| 114 | SCSI Bus Reset |
| 115 | SCSI Bus Parity Error |
| 116 | Request Sense Failed |
| 117 | Target Didn't Respond to Selection Error |
| 118 | Data Under/Over run |
| 119 | SCSI Bus Free Error |
| 120 | SCSI Phase Error |
| 126 | Bad Scatter/Gather List Error |
| 178 | Invalid SCSI Request |
| 179 | Invalid Host Adapter |
| 180 | Invalid SCSI Target |
| SCSI CODE | COMMAND FINISHED WITH SCSI CHECK CONDITION ERRORS |
| 200 | Ok |
| 202 | Check Condition |
| 208 | Target Is Busy |
| 216 | Intermediate Status |
| 232 | Cmd Aborted |
| 234 | Cmd Terminated |
| 240 | Target Queue Full |
| 274 | Invalid SRB |
| 275 | Transfer Buffer Alignment Error |
| 279 | Adapter is Busy |
| 280 | Transfer Buffer Too Large |
| 281 | Invalid Path |
| 500 | End Of Media |
| 1000 | No Sense |
| 1001 | Recovered |
| 1002 | Not Ready |
| 1003 | Medium |
| 1004 | Hardware |
| 1005 | Illegal Request |
| 1006 | Unit Attention |
| 1007 | Write Protect |
| 1008 | Blank Check |
| 1009 | Vendor Unique |
| 1010 | Copy Aborted |
| 1011 | Aborted Command |
| 1012 | Equal |
| 1013 | Volume Overflow |
| 1014 | Miscompare |
| 1015 | Last |
| 2000 | No Additional Sense |
| 2001 | I/O Process Terminated |
| 2002 | No Seek Complete |
| 2003 | Write Fault |
| 2004 | LUN Not Ready |
| 2005 | LUN Doesn't Respond To Selection |
| 2006 | No Reference Position |
| 2007 | LUN Multiple Peripherals Selected |
| 2008 | LUN Parity Error |
| 2009 | Track Following Error |
| 2010 | Error Log Overflow |
| 2012 | Write Error |
| 2016 | CRC Error |
| 2017 | Unrecovered Read Error |
| 2018 | ID Address Mark Not Found |
| 2019 | Data Address Mark Not Found |
| 2020 | Record Not Found |
| 2021 | Positioning Error |
| 2022 | Data Synchronization Error |
| 2023 | Recovered Data |
| 2024 | Recovered Data with ECC |
| 2025 | Defect List Error |
| 2026 | Parameter List Length Error |
| 2027 | Synchronous Data Transfer Error |
| 2028 | Defect List Not Found |
| 2029 | Miscompare |
| 2030 | Recovered ID with ECC |
| 2032 | Invalid Command Op Code |
| 2033 | Logical Block Address Out Of Range |
| 2034 | Logical Unit Not Supported |
| 2036 | Invalid Field in CDB |
| 2037 | Logical Unit Not Supported |
| 2038 | Invalid Field In Parameter List |
| 2039 | Write Protected |
| 2040 | Ready Transition |
| 2041 | Reset Occured |
| 2042 | Mode Parameters Changed |
| 2043 | Copy Cannot Execute Since Host Cannot Disconnect |
| 2044 | Command Sequence |
| 2047 | Tagged Commands Cleared By another Initiator |
| 2048 | Incompatible Medium Installed |
| 2049 | Medium Format Corrupted |
| 2050 | Defect List Update Failure |
| 2055 | Rounded Parameter |
| 2057 | Saving Parameters Not Supported |
| 2058 | Medium Not Present |
| 2061 | Invalid Bits in IDENTIFY Message |
| 2062 | Logical unit Has not Self Configured Yet |
| 2063 | Target Operating Conditions Have Changed |
| 2064 | Diagnostic Failure On Component |
| 2067 | Message Error |
| 2068 | Internal Target Failure |
| 2069 | Select/Reselect Failure |
| 2070 | Unsuccessful Soft Reset |
| 2071 | SCSI Parity |
| 2072 | Initiator Detected Error Message Received |
| 2073 | Invalid Message Error |
| 2074 | COMMAND Phase |
| 2075 | DATA Phase |
| 2076 | Logical Unit Failed Self Configuration |
| 2078 | Overlapped Commands Rejected |
| 2083 | Media Load/Eject Failed |
| 2090 | Operator Request |